Specifier
notes are shown in italics and should be deleted from the final document. Generally all of the manufacturer’s products
in this category are listed and the specifier must take care to delete those
products not included in the project.
Depending
on the relative complexity of the project, the specifier may choose to combine
two or more Compartment and Cubicle Sections into one Section, Section 10150
Compartments and Cubicles, corresponding to the CSI MasterFormatä.
Edit
each Article in this Section to suit project requirements.
SECTION
10165
PLASTIC LAMINATE TOILET
COMPARTMENTS
1.01
SECTION
INCLUDES
A.
Overhead
braced, floor mounted plastic laminate compartments.
B.
Floor
mounted and braced plastic laminate compartments.
C.
Ceiling
hung plastic laminate compartments.
D.
Floor
mounted, ceiling braced plastic laminate compartments.
E.
Plastic
laminate privacy and urinal screens.
E. Hardware and fittings.
1.02
RELATED
SECTIONS
A.
Section
(select Sections that describe the
anchoring substrate: floor, walls and/or ceiling)
B.
Section
10810-Toilet Accessories
1.03
REFERENCES
A.
B.
ANSI
A208.1 – Wood Particleboard.
C.
ASTM
A666 – Standard Specification for Austenitic Stainless Steel Sheet, Strip,
Plate, and Flat Bar.
D.
NEMA
LD 3 – High Pressure Decorative Laminates.
1.04
SUBMITTALS
A.
Provide
submittals in accordance with Conditions of the Contract and Section
01330-Submittal Procedures.
B.
Submit
shop drawings showing layout, door swings, profiles, and product components, including
anchorage, accessories and finish colors.
C.
Submit
product data on panel construction, hardware, and accessories.
D.
Submit
two samples 4 x 4 inch (102 x 102 mm) in size illustrating panel finish, color,
and sheen.
E.
Submit
maintenance data for installed products in accordance with Section
01780-Closeout Submittals.
1.05
DELIVERY,
STORAGE AND HANDLING
A.
Generally
comply with provisions of Section 01600-Product Requirements.
B.
Comply
with manufacturer’s ordering instructions and lead time requirements to avoid
construction delays.
C.
Deliver
materials in manufacturer’s original, unopened, undamaged containers with
identification labels intact.
D.
Store
materials indoors, in a supported vertical position, protected from weather
conditions and construction activities.
1.06
PROJECT
CONDITIONS
A.
Building
enclosed, completely protected from outside weather with minimum inside
temperature of 60°F.
1.07
WARRANTY
A.
Provide
manufacturer’s three year warranty against discoloration and delamination of
panels.
B.
Provide
manufacturer’s five year warranty for chrome hardware and lifetime warranty for
stainless steel hardware.
2.01
MANUFACTURERS
A.
The
Mills Company, a subsidiary of Bradley Corporation, P.O. Box 309, Menomonee
Falls, WI 53052-0309. Phone 800-BRADLEY
(800-272-3539), Fax 262-251-5817.
http://www.bradleycorp.com
B.
Substitutions:
[Section 01600 – Product Requirements] [Not Permitted].
2.02
MANUFACTURED
UNITS
A.
Overhead
braced compartments, “Sentinel”–Series 400 (specify
laminate manufacturer, color and options).
B.
Floor
mounted and braced compartments, Series 500 (specify
laminate manufacturer, color and options).
C.
Ceiling
hung compartments, Series 600 (specify
laminate manufacturer, color and options).
D.
Floor
mounted and ceiling braced compartments, Series 700 (specify laminate manufacturer, color and options).
E.
Privacy
and urinal screens, panels (specify
laminate manufacturer, color and options).
2.03
COMPONENTS
A.
Panels
and doors 1 inch (25 mm) thick, consisting of 0.48 high pressure plastic
laminate bonded to 45 pound density industrial grade particleboard using non
toxic adhesive.
1.
Plastic
laminate shall meet or exceed NEMA standards.
2.
Laminate
door and panel edges before faces to achieve maximum protection from moisture
penetration.
B.
Pilasters
1-¼ inch (32 mm) thick, same construction as panels and doors, with 3/8 inch
(10 mm) threaded rods for [floor] [ceiling] anchoring, and hex nuts and washers
for adjustment.
2.04
Accessories
A.
Four
piece pilaster shoes, 4 inch (102 mm) high 300 series stainless steel, anchored
in place with chrome plated screws.
B.
Head
Rails: 1-1/4 x 1-1/2 inch (25 x 38 mm) anodized aluminum tube with anti-grip
profile and cast socket wall brackets.
C.
Brackets:
[Chrome-plated non-ferrous cast metal]
[stainless steel with brushed finish].
D.
Fasteners,
screws and bolts: Tamper proof [chrome-plated] [stainless steel].
E.
Hardware:
[Chrome-plated non-ferrous cast metal] [stainless steel].
1.
Wrap
around hinge brackets through-bolted to pilasters for gravity cams.
2.
Surface
mounted slide latch with emergency egress release, meeting
3.
Wrap
around door strike/keeper.
4.
Coat
hook with rubber wall bumper; one per compartment, mounted on door.
5.
Door
pull and door stop for each out swinging door.
3.01
EXAMINATION
A.
Verify
that finishes and plumbing are complete and acceptable for the installation of
toilet compartments.
B.
Verify
field measurements are as shown on approved shop drawings.
C.
Verify
correct spacing of plumbing fixtures.
D.
Verify
correct location of built-in framing, blocking, anchorage, and bracing.
3.02
INSTALLATION
A.
Comply
with manufacturer’s written instructions and approved shop drawings for
installation of compartments.
B.
Anchor
panel brackets to construction using anchors suitable for supporting substrate.
C.
Attach
panels and pilasters to brackets. Locate head rail joints at pilaster
centerlines.
D.
Attach
clamp design head rail over pilaster and secure to front with screws.
3.03
ADJUSTING
A.
Section
01700 – Execution Requirements: Testing, adjusting, and balancing.
B.
Adjust
and align hardware to uniform clearance at vertical edge of doors, not
exceeding 3/16 inch (5 mm).
C.
Adjust
hinges to position doors in [partially]
[fully] opened position when unlatched.
Return out swinging doors to closed position. (Note:
Out swinging doors require wall or panel to limit door travel to maximum 105
degrees.)
D.
Correct
minor damage to installed products; remove and replace work that cannot be
satisfactorily repaired.
3.04
CLEANING
A.
Remove
packaging and construction debris, and legally dispose of off-site.
3.05
SCHEDULE
(Where multiple units are specified, it might
be best to give them a “mark” and
create a schedule).